
Quick answer: Heat transfer viva questions cover the three modes (conduction, convection, radiation), Fourier’s law and thermal conductivity, convection coefficients and dimensionless numbers, fins, heat exchangers (LMTD and NTU methods) and common lab experiments. Short, clear answers to the most asked questions are below.
Answers are written in a short, exam-style form so you can say them confidently in your viva. Prepared by Engineers R World, guiding mechanical and aerospace students since 2013.
Contents
Basics and Conduction
What are the modes of heat transfer?
Conduction (through solids by molecular interaction), convection (between a surface and a moving fluid) and radiation (by electromagnetic waves, without a medium).
State Fourier’s law of heat conduction.
The heat flow rate by conduction is proportional to the area and the temperature gradient: Q = −kA (dT/dx), where k is thermal conductivity.
What is thermal conductivity?
The ability of a material to conduct heat, in W/m·K. Metals have high conductivity (copper about 385–400 W/m·K); insulators have low conductivity.
What is thermal resistance?
The opposition to heat flow, analogous to electrical resistance. For a plane wall R = L/(kA); for convection R = 1/(hA).
What is critical radius of insulation?
The radius at which adding insulation to a cylinder gives maximum heat loss: r_c = k/h. Below this radius, adding insulation increases heat loss.
What is thermal diffusivity?
α = k/(ρc_p). It shows how quickly a material responds to temperature changes.
Convection
State Newton’s law of cooling.
Q = hA(T_s − T_∞), where h is the convective heat transfer coefficient.
What is the difference between free and forced convection?
Free (natural) convection is driven by buoyancy due to density differences; forced convection uses an external device such as a fan or pump.
What is the Nusselt number?
Nu = hL/k. It is the ratio of convective to conductive heat transfer across a fluid layer.
What is the Prandtl number?
Pr = ν/α = μc_p/k. It compares momentum diffusivity with thermal diffusivity.
What is the Grashof number?
The ratio of buoyancy to viscous forces, used in natural convection problems.
What is the Reynolds number?
Re = ρVL/μ, the ratio of inertia to viscous forces. It decides whether flow is laminar or turbulent.
Radiation
What is a black body?
An ideal body that absorbs all incident radiation and emits the maximum possible radiation at a given temperature.
State the Stefan–Boltzmann law.
The emissive power of a black body is E_b = σT⁴, where σ = 5.67 × 10⁻⁸ W/m²K⁴.
What is emissivity?
The ratio of emissive power of a real surface to that of a black body at the same temperature (0 to 1).
What is Kirchhoff’s law of radiation?
At thermal equilibrium, the emissivity of a surface equals its absorptivity.
What is a view factor?
The fraction of radiation leaving one surface that directly reaches another surface.
Fins and Heat Exchangers
Why are fins used?
To increase the surface area for heat transfer by convection – for example on engine cylinders, motorcycle heads and electronic heat sinks.
What is fin efficiency?
The ratio of actual heat transfer from the fin to the heat transfer if the entire fin were at base temperature.
What is fin effectiveness?
The ratio of heat transfer with the fin to heat transfer without the fin from the same base area. Fins are worthwhile when effectiveness is well above 1.
What are the types of heat exchangers?
By flow: parallel flow, counter flow and cross flow. By construction: double pipe, shell-and-tube, plate and compact heat exchangers.
Why is counter flow more effective than parallel flow?
Counter flow keeps a more uniform temperature difference along the length, giving a higher LMTD and allowing the cold fluid outlet to exceed the hot fluid outlet temperature.
What is LMTD?
Log Mean Temperature Difference – the effective average temperature difference used in Q = UA·LMTD.
When is the NTU method used?
When outlet temperatures are unknown, the effectiveness–NTU method is used to find heat transfer and outlet temperatures directly.
What is fouling?
Deposits on heat exchanger surfaces that add thermal resistance and reduce performance over time.
Heat Transfer Lab Viva Questions
What is the aim of the composite wall experiment?
To find the overall thermal conductance and verify the thermal resistance concept for walls of different materials in series.
Why is a guard heater used in some conduction experiments?
To minimise radial or side heat loss so that heat flows in one direction, matching the assumption of one-dimensional conduction.
What is measured in the pin fin apparatus?
Temperature distribution along the fin under natural and forced convection, to find fin efficiency and effectiveness.
What is the Stefan–Boltzmann apparatus used for?
To determine the Stefan–Boltzmann constant experimentally using a hemispherical enclosure and a test disc.
Tips to Answer Viva Questions Confidently
- Write units with every formula – examiners check them.
- Relate each mode to a real example (radiator, heat sink, solar collector).
- Know the formula and the meaning of each symbol.
Related Viva Questions and Guides
- Heat transfer formulas and notes
- Thermodynamics viva questions
- Fluid mechanics viva questions
- ANSYS viva questions
- All viva question banks
Need Viva Preparation?
Book a mock viva and PPT review with us, or send your project details through the enquiry form or WhatsApp.