
Quick answer: Fluid mechanics viva questions usually cover fluid properties, pressure measurement, Bernoulli’s equation and its applications (venturimeter, orifice meter, pitot tube), laminar and turbulent flow, pipe losses, and basic pumps and turbines from the fluid mechanics and machinery lab.
Answers are written in a short, exam-style form so you can say them confidently in your viva. Prepared by Engineers R World, guiding mechanical and aerospace students since 2013.
Contents
- Fluid Properties and Statics
- Fluid Kinematics and Dynamics
- Flow Measurement (Lab)
- Flow Through Pipes
- Pumps and Turbines
Fluid Properties and Statics
What is a fluid?
A substance that deforms continuously under the action of a shear stress, however small. Liquids and gases are fluids.
What is viscosity?
The property of a fluid that resists relative motion between its layers. Dynamic viscosity μ is in Pa·s; kinematic viscosity ν = μ/ρ is in m²/s.
What is the difference between Newtonian and non-Newtonian fluids?
Newtonian fluids (water, air) have shear stress directly proportional to velocity gradient; non-Newtonian fluids (blood, paint) do not.
What is surface tension?
The tensile force per unit length at a liquid surface due to cohesion, which makes the surface behave like a stretched membrane.
What is the difference between absolute and gauge pressure?
Absolute pressure is measured from perfect vacuum; gauge pressure is measured relative to atmospheric pressure. Absolute = gauge + atmospheric.
State Pascal’s law.
Pressure at a point in a fluid at rest is equal in all directions.
Fluid Kinematics and Dynamics
What is the continuity equation?
For steady incompressible flow, A₁V₁ = A₂V₂ – mass flow rate stays constant along a pipe.
State Bernoulli’s equation and its assumptions.
p/ρg + V²/2g + z = constant along a streamline, for steady, incompressible, inviscid flow without shaft work or heat transfer.
What are the applications of Bernoulli’s equation?
Venturimeter, orifice meter, pitot tube, aircraft lift explanation, and flow from tanks.
What is the difference between laminar and turbulent flow?
Laminar flow moves in smooth layers at low Reynolds number; turbulent flow is chaotic with mixing at high Reynolds number. In pipes, flow is generally laminar below Re ≈ 2000 and turbulent above about 4000.
What is a streamline?
An imaginary line whose tangent at every point gives the direction of velocity at that instant.
Flow Measurement (Lab)
What is the principle of a venturimeter?
The flow accelerates in the converging throat, pressure drops, and the pressure difference measured by a manometer gives the flow rate using Bernoulli and continuity equations.
What is the coefficient of discharge?
The ratio of actual discharge to theoretical discharge. It is less than 1 due to losses; typically about 0.95–0.98 for a venturimeter and about 0.6–0.65 for an orifice meter.
Why is the venturimeter more accurate than the orifice meter?
Its gradual convergence and divergence reduce losses and flow separation, so actual flow is closer to theoretical.
What is vena contracta?
The section of a jet just downstream of an orifice where the area is minimum and velocity is maximum.
What is a pitot tube used for?
To measure local flow velocity from the difference between stagnation pressure and static pressure.
Flow Through Pipes
What are major and minor losses?
Major losses are due to friction along the pipe length; minor losses are due to fittings, bends, valves, sudden expansion and contraction.
State the Darcy–Weisbach equation.
h_f = fLV²/(2gD), giving head loss due to friction in a pipe, where f is the Darcy friction factor.
What is the friction factor for laminar flow?
f = 64/Re (Darcy friction factor).
What is a Moody diagram?
A chart giving friction factor as a function of Reynolds number and relative roughness of the pipe.
Pumps and Turbines
What is the difference between a centrifugal pump and a reciprocating pump?
A centrifugal pump uses a rotating impeller to add kinetic energy (high flow, moderate head); a reciprocating pump uses a piston to displace fluid (low flow, high head).
What is priming?
Filling the suction pipe and pump casing with liquid before starting a centrifugal pump, to remove air so the pump can develop suction.
What is cavitation?
Formation and collapse of vapour bubbles where local pressure falls below vapour pressure, causing noise, vibration and pitting of blades.
What is NPSH?
Net Positive Suction Head – the margin of pressure head above vapour pressure at the pump suction. Available NPSH must exceed required NPSH to avoid cavitation.
What are impulse and reaction turbines?
In impulse turbines (Pelton wheel) all pressure energy is converted to kinetic energy in nozzles; in reaction turbines (Francis, Kaplan) pressure drops partly in the runner.
Which turbine is used for high head and which for low head?
Pelton wheel for high head and low flow, Francis for medium head, Kaplan for low head and high flow.
Tips to Answer Viva Questions Confidently
- Sketch the venturimeter or pump while answering.
- Remember typical values of Cd and Reynolds number limits.
- Explain each lab formula and the reading you took from the manometer.
Related Viva Questions and Guides
- Fluid mechanics formulas and notes
- Heat transfer viva questions
- Aerodynamics viva questions
- Centrifugal pump impeller project
- All viva question banks
Need Viva Preparation?
Book a mock viva and PPT review with us, or send your project details through the enquiry form or WhatsApp.