
Quick answer: Aerodynamics viva questions focus on lift and drag, airfoil terminology, angle of attack and stall, induced drag and wing design, boundary layers, compressibility (Mach number, shock waves) and wind tunnel testing. These are also common in aeronautical interviews.
Answers are written in a short, exam-style form so you can say them confidently in your viva. Prepared by Engineers R World, guiding mechanical and aerospace students since 2013.
Contents
- Lift, Drag and Airfoils
- Stall, Induced Drag and Wing Design
- Boundary Layer and Flow Behaviour
- Compressible Flow
- Wind Tunnel and CFD
Lift, Drag and Airfoils
How is lift produced?
An airfoil turns the airflow downward and creates lower pressure on the upper surface than on the lower surface. The pressure difference over the wing area produces lift, explained by Bernoulli’s principle and Newton’s third law together.
What is the lift equation?
L = ½ρV²SC_L, where ρ is air density, V is velocity, S is wing area and C_L is lift coefficient.
What are the types of drag?
Parasite drag (skin friction, form/pressure drag, interference drag), induced drag (due to lift and wingtip vortices) and wave drag at transonic and supersonic speeds.
Define chord, camber and angle of attack.
Chord is the straight line from leading edge to trailing edge; camber is the curvature of the mean line; angle of attack is the angle between the chord line and the relative wind.
What does NACA 2412 mean?
Maximum camber 2% of chord, located at 40% of chord, with maximum thickness 12% of chord.
What is the lift-to-drag ratio?
L/D, a measure of aerodynamic efficiency. Maximum L/D gives best glide ratio and maximum range for propeller aircraft.
Stall, Induced Drag and Wing Design
What is stall?
A sudden loss of lift when the angle of attack exceeds the critical angle and the flow separates from the upper surface of the wing.
What is induced drag and how is it reduced?
Drag caused by wingtip vortices that tilt the lift vector backward. It is reduced by higher aspect ratio, winglets and elliptical lift distribution.
What is aspect ratio?
AR = b²/S (span squared divided by wing area). High aspect ratio wings have lower induced drag, as on gliders.
How do winglets work?
They weaken wingtip vortices and recover some energy from the swirling flow, reducing induced drag and fuel consumption.
What are flaps and slats used for?
High-lift devices: flaps increase camber and wing area, slats delay flow separation at the leading edge, allowing lower take-off and landing speeds.
Why are swept wings used?
Sweep delays the rise in drag near the speed of sound by reducing the effective Mach number normal to the leading edge.
Boundary Layer and Flow Behaviour
What is a boundary layer?
The thin layer near a surface where velocity changes from zero at the wall (no-slip) to the free-stream value.
What is flow separation?
When the boundary layer cannot overcome an adverse pressure gradient, it detaches from the surface, causing pressure drag and loss of lift.
What is the role of Reynolds number in aerodynamics?
It decides laminar or turbulent boundary layer behaviour and strongly affects skin friction, separation and maximum lift coefficient.
What are vortex generators?
Small vanes on the wing that energise the boundary layer, delaying separation and improving control at high angles of attack.
Compressible Flow
What is Mach number?
The ratio of flow velocity to the local speed of sound, M = V/a.
What are the speed regimes?
Subsonic (M < 0.8), transonic (0.8–1.2), supersonic (1.2–5) and hypersonic (M > 5), approximately.
What is a shock wave?
A very thin region across which pressure, temperature and density rise sharply and velocity drops, formed in supersonic flow.
What is critical Mach number?
The free-stream Mach number at which the local flow somewhere on the body first reaches Mach 1.
What is the difference between normal and oblique shocks?
A normal shock is perpendicular to the flow and makes it subsonic behind it; an oblique shock is inclined and the flow behind it may remain supersonic.
Wind Tunnel and CFD
What are the types of wind tunnels?
Open-circuit and closed-circuit tunnels; by speed, low-speed, transonic, supersonic and hypersonic tunnels.
Why are scale models used in wind tunnels?
Full-size testing is impractical; similarity parameters such as Reynolds number and Mach number are matched as closely as possible.
How is lift measured in a wind tunnel?
Using a force balance, or by integrating surface pressures measured with pressure taps and a manometer or scanner.
How is airfoil CFD validated?
By comparing lift and drag coefficients versus angle of attack with published experimental data for the same airfoil and Reynolds number.
Tips to Answer Viva Questions Confidently
- Draw an airfoil and label chord, camber and angle of attack.
- Know the lift equation and NACA 4-digit meaning – they are asked in almost every viva.
- Relate answers to your project, for example winglet or airfoil CFD.
Related Viva Questions and Guides
- Aerodynamics formulas and notes
- Aeronautical engineering project ideas
- Parts of an aircraft explained
- Fluid mechanics viva questions
- GATE Aerospace roadmap
- All viva question banks
Need Viva Preparation?
Book a mock viva and PPT review with us, or send your project details through the enquiry form or WhatsApp.