The main parts of an aircraft are the fuselage, wings, empennage (tail), landing gear and powerplant (engines). Control surfaces on the wings and tail, such as ailerons, elevators and the rudder, let the pilot steer the aircraft in roll, pitch and yaw. This guide explains every part of an aircraft and its function in simple terms.
Main parts of an aircraft at a glance
| Part | Main function |
|---|---|
| Fuselage | Main body; carries crew, passengers, cargo and connects all parts |
| Wings | Produce lift; carry fuel tanks, flaps and ailerons |
| Empennage (tail) | Gives stability and control in pitch and yaw |
| Landing gear | Supports the aircraft on the ground, for take-off and landing |
| Powerplant | Engines and propellers that produce thrust |
| Cockpit and avionics | Flight controls, instruments, navigation and communication |
1. Fuselage
The fuselage is the central body of the aircraft. It holds the cockpit, cabin and cargo hold, and the wings, tail and often the landing gear are attached to it. Most modern airliners use a semi-monocoque structure: a thin skin supported by frames (formers) and longitudinal stringers, so the skin and the frame share the loads. Sections of the fuselage are joined with splice joints, which are a common topic for stress and fatigue analysis.
2. Wings
Wings have an airfoil cross-section that creates lift when air flows over them. The inside structure consists of spars (main span-wise beams that carry bending loads) and ribs (which keep the airfoil shape), covered by the skin. Wings also store fuel in many aircraft.
Parts on the wing
- Ailerons: hinged surfaces near the wing tips that move in opposite directions to roll the aircraft.
- Flaps: on the trailing edge near the fuselage; they increase lift and drag for slow take-off and landing.
- Slats: on the leading edge; they let the wing fly at higher angles of attack without stalling.
- Spoilers: panels on the top surface that reduce lift and increase drag, used to descend and to slow down after landing.
- Winglets: upturned wing tips that reduce wing-tip vortices and induced drag, saving fuel.
3. Empennage (tail section)
The empennage keeps the aircraft stable, like the feathers of an arrow.
- Horizontal stabiliser: provides pitch stability. The hinged elevator at its rear controls pitch (nose up or down).
- Vertical stabiliser (fin): provides directional stability. The hinged rudder controls yaw (nose left or right).
- Trim tabs: small surfaces that hold a control surface in position so the pilot does not need to apply constant force.
4. Landing gear
The landing gear supports the aircraft on the ground and absorbs landing loads using shock struts (oleo struts). The two common layouts are tricycle (nose wheel and two main wheels, used by most modern aircraft) and tailwheel (two main wheels and a small tail wheel). Many aircraft retract the gear after take-off to reduce drag. The main wheels have brakes; aircraft wheel hubs and disc brakes are designed for very high loads and temperatures.
5. Powerplant
The powerplant produces thrust. Small aircraft use piston engines driving propellers. Airliners use turbofan engines, and some regional aircraft use turboprops. Engines are housed in a nacelle and mounted on the wing or fuselage using a pylon. Learn how they work on our Aircraft Propulsion notes.
6. Cockpit and avionics
The cockpit (flight deck) contains the flight controls (control column or side-stick, rudder pedals, throttles) and the instruments. Avionics are the electronic systems for navigation, communication, autopilot and engine monitoring.
Three axes of flight and their controls
| Motion | Axis | Control surface |
|---|---|---|
| Roll | Longitudinal axis (nose to tail) | Ailerons |
| Pitch | Lateral axis (wing tip to wing tip) | Elevator |
| Yaw | Vertical (normal) axis | Rudder |
Four forces acting on an aircraft
- Lift: produced by the wings, acts upward
- Weight: due to gravity, acts downward
- Thrust: produced by the engines, acts forward
- Drag: air resistance, acts backward
In steady level flight, lift equals weight and thrust equals drag. See the lift and drag equations on our Aerodynamics notes and Flight Mechanics notes.
FAQs on parts of an aircraft
What are the five main parts of an aircraft?
Fuselage, wings, empennage (tail), landing gear and powerplant.
Which control surface controls roll?
The ailerons on the outer trailing edge of the wings control roll.
What is the difference between flaps and ailerons?
Flaps move together on both wings to increase lift for take-off and landing; ailerons move in opposite directions to roll the aircraft.
What is the empennage?
The tail section of the aircraft, made up of the horizontal and vertical stabilisers with the elevator and rudder.
Interested in this project? Get the details, files and guidance from our team.
Enquire on WhatsApp