Two-Wheeler Piston and Connecting Rod: Static and Thermal Analysis with Design Optimisation

The piston receives the push of the burning gases in the cylinder and passes it to the crankshaft through the connecting rod. The piston crown faces combustion temperatures and pressures on every power stroke, while also having to carry heat away to the cylinder walls through its rings. The connecting rod carries the gas force as compression and the inertia of the piston as tension. Both parts must be strong and light, because lighter reciprocating parts allow higher engine speeds with less vibration.

Two-wheeler piston model in Creo

Design Calculations

The piston and connecting rod are designed for a two-wheeler engine with a maximum power of 13.8 bhp at 8500 rpm and a maximum torque of 13.4 Nm at 6000 rpm. From the engine data, the maximum gas pressure works out to about 15.4 N/mm², and the main dimensions of the piston crown, ring lands, skirt and pin are calculated from standard design equations.

Connecting rod model in Creo
Connecting rod

About the Project

The parts are modelled in Creo and analysed in ANSYS Workbench:

  • Piston static analysis: a gas pressure of 12 MPa on the crown, for the original piston and for a modified piston with the ring thickness reduced by 2 mm.
  • Piston thermal analysis: convection at 650 °C on the crown (7 × 10⁻⁴ W/mm²·°C), and at 225 °C and 180 °C on the ring and skirt areas.
  • Connecting rod static analysis: a pressure of 8 MPa.

The piston is compared in steel and aluminium alloy. The connecting rod is compared in an aluminium alloy and an aluminium composite reinforced with silicon carbide and fly ash.

Piston mesh in ANSYS
Mesh

Software Used

  • Creo: piston and connecting rod modelling
  • ANSYS Workbench: static structural and steady-state thermal analysis

Piston Static Results

Piston 12 MPa gas pressure boundary condition
Boundary conditions
Piston designMaterialStress (MPa)Shear stress (MPa)Safety factor
OriginalSteel261.2137.861.072
OriginalAluminium alloy255.77135.11.388
Modified ringsSteel163.4888.1951.7127
Modified ringsAluminium alloy159.386.0912.288
Piston equivalent stress
Equivalent stress

Piston Thermal Results

Piston thermal convection boundary conditions
Thermal boundary conditions
Piston designMaterialMax temperature (°C)Total heat flux (W/mm²)
OriginalSteel288.60.63589
OriginalAluminium alloy252.371.1611
Modified ringsSteel292.760.91837
Modified ringsAluminium alloy258.591.5507
Piston temperature distribution
Temperature

Connecting Rod Results

MaterialDeformation (mm)Stress (MPa)Safety factor
Aluminium alloy (Al-3600)0.2476111.81.5206
Al-SiC-fly ash composite0.21226111.83.247
Connecting rod equivalent stress
Connecting rod stress

Reducing the ring thickness lowers the piston stress for both materials. The full discussion and the final recommendation are explained in the project report.

Real-World Applications

  • Motorcycles and scooters: single cylinder engines.
  • Cars: multi-cylinder petrol and diesel engines.
  • Small generators and pumps.
  • Aluminium metal matrix composites for lightweight engine parts.

Key Concepts Covered

  • Piston design calculations from engine power and torque.
  • Design optimisation by changing ring geometry.
  • Thermal loading of piston crowns.
  • Metal matrix composites: SiC and fly ash reinforcement.

Project Workflow

  1. Calculate piston and connecting rod dimensions from engine data.
  2. Model the piston, modified piston and connecting rod in Creo.
  3. Run static and thermal analysis of the piston in steel and aluminium alloy.
  4. Run static analysis of the connecting rod in two materials.
  5. Compare results in the report.

Why This Project Matters

The piston and connecting rod are among the most stressed parts of any engine. This project combines design calculations, optimisation and FEA, a complete package for mechanical and automobile students.

Related Projects

Explore more design and analysis projects on similar topics:

What You Get

  • Design files: Creo models of the original and modified piston and the connecting rod, with design calculations
  • Analysis files: ANSYS Workbench static structural and steady-state thermal files for the piston, and static files for the connecting rod
  • Project document: complete report with methodology, results and conclusion
  • Class explanation: a session that explains what was done in the project, step by step, so you can understand and present it confidently

Who Is This Project For?

This project suits B.Tech and B.E. final year students, diploma students looking for a strong design and analysis project, and M.Tech students who need a base model they can extend for their thesis. It is also useful for anyone who wants to learn engine component design calculations, Creo modelling and ANSYS structural and thermal analysis on a real engineering problem instead of a textbook example.

Frequently Asked Questions

Which engine is the piston designed for?

A two-wheeler engine with 13.8 bhp at 8500 rpm and 13.4 Nm at 6000 rpm.

How is the piston optimised?

The piston ring thickness is reduced by 2 mm and the modified piston is analysed with the same loads.

What thermal loads are applied?

Convection at 650 °C on the crown, with lower temperatures of 225 °C and 180 °C on the ring and skirt areas.

Which materials are used for the connecting rod?

An aluminium alloy and an aluminium composite reinforced with silicon carbide and fly ash.

Get the Piston and Connecting Rod Project

Want this project for your final year, mini project or M.Tech work? Message us with your university, branch and deadline, and we will share the exact scope, files and report format.

Enquire about this project on WhatsApp or use the enquiry form on our home page. Browse more mechanical projects or 60+ mechanical engineering project ideas.

Interested in this project? Get the details, files and guidance from our team.

Enquire on WhatsApp

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top