The exhaust manifold is the first part of an engine’s exhaust system. It bolts directly onto the cylinder head and collects the hot exhaust gases from each cylinder into a single pipe. Because it sits right next to the combustion chambers, it faces very high gas temperatures, rapid heating and cooling every time the engine starts and stops, internal gas pressure, and vibration. Cracks at the flanges and end connections due to thermal stress are one of the most common manifold failures. This project designs two exhaust manifolds for an off-road vehicle diesel engine and compares them with four materials.


What Makes a Good Exhaust Manifold?
A good manifold must be strong at high temperature, resist thermal fatigue, and guide the exhaust gases smoothly so that back pressure stays low. Most manifolds are made from cast iron or nodular iron, and some from stainless or heavy-gauge steel. The shape of the runners and the junction where they merge strongly affects stress, heat transfer and gas flow, which is why this project compares two different designs as well as different materials.
About the Project
Two manifold designs are modelled in SolidWorks and analysed in ANSYS Workbench with four materials: steel (the existing material), EN-9, grey cast iron and Steel 440C. Three types of analysis are carried out:
- Static structural analysis: the mounting face is fixed and an internal pressure of 0.5 MPa is applied.
- Steady-state thermal analysis: the inner surfaces see exhaust gas at 500 °C with a film coefficient of 70 W/m²·°C, and the outer surfaces lose heat to air at 25 °C with a film coefficient of 30 W/m²·°C.
- CFD analysis in ANSYS Fluent: exhaust gas enters at a mass flow rate of 0.000424 kg/s and a temperature of 900 K, giving the pressure, velocity and temperature distribution inside the manifold.

Software Used
- SolidWorks: 3D manifold modelling
- ANSYS Workbench: static structural and steady-state thermal analysis
- ANSYS Fluent: CFD flow analysis
Analysis Results





Key Results (Preview)
| Material | Stress, design 1 (MPa) | Stress, design 2 (MPa) | Safety factor, design 1 | Safety factor, design 2 |
|---|---|---|---|---|
| Steel | 161.15 | 141.42 | 1.5514 | 1.7678 |
| EN-9 | 161.44 | 141.65 | 2.1989 | 2.5061 |
| Grey cast iron | 161.73 | 141.87 | 1.892 | 2.1568 |
| Steel 440C | 163.26 | 142.86 | 2.7563 | 3.15 |
| Material | Heat flux, design 1 (W/m²) | Heat flux, design 2 (W/m²) |
|---|---|---|
| Steel | 74572 | 1.3015 × 10⁵ |
| Grey cast iron | 72271 | 1.2604 × 10⁵ |
| Steel 440C | 61731 | 1.0376 × 10⁵ |
| EN-9 | 55811 | 91644 |
The second design lowers the stress by about 20 MPa for every material and transfers heat much faster. The temperature and deformation results, the CFD findings and the final design and material recommendation are explained in the project report.
Project Workflow
- Study exhaust manifold failures and select candidate materials.
- Model two manifold designs in SolidWorks.
- Run the static analysis at 0.5 MPa for both designs and all four materials.
- Run the steady-state thermal analysis with inner and outer convection.
- Run the CFD analysis with exhaust gas at 900 K.
- Compare designs and materials in the report.
Why This Project Matters
The exhaust manifold combines structural, thermal and fluid flow problems in one automobile part. This project gives students experience with all three types of analysis, which makes it an excellent final-year project for mechanical and automobile engineering students.
Related Projects
Explore more design and analysis projects on similar topics:
- CFD Analysis of a Diesel Engine Combustion Chamber with Diesel and Rice Husk Biofuel Blends (SolidWorks and ANSYS Fluent)
- Design and Analysis of an Engine Mount Bracket: AISI 4140, Al 7075 and Ti-6Al-4V (SolidWorks and ANSYS)
- Reciprocating Compressor Valve Plate Design and Analysis: Five Slot Designs Compared (Creo and ANSYS)
- Li-ion Battery Pack Thermal Management with Paraffin PCM and Copper Tube Water Cooling (SolidWorks and ANSYS)
What You Get
- Design files: SolidWorks 3D models of both exhaust manifold designs
- Analysis files: ANSYS static structural, steady-state thermal and Fluent CFD analysis files
- Project document: complete report with methodology, results and conclusion
- Class explanation: a session that explains what was done in the project, step by step, so you can understand and present it confidently
Who Is This Project For?
This project suits B.Tech and B.E. final year students, diploma students looking for a strong design and analysis project, and M.Tech students who need a base model they can extend for their thesis. It is also useful for anyone who wants to learn exhaust manifold design, structural, thermal and CFD analysis in ANSYS on a real engineering problem instead of a textbook example.
Frequently Asked Questions
What does an exhaust manifold do?
It collects the hot exhaust gases from each cylinder and sends them into a single exhaust pipe.
Which materials are compared?
Steel (the existing material), EN-9, grey cast iron and Steel 440C are compared for both designs.
What thermal conditions are used?
Exhaust gas at 500 °C with a film coefficient of 70 W/m²·°C acts on the inner surfaces, and air at 25 °C with 30 W/m²·°C acts on the outer surfaces.
What does the CFD analysis show?
It shows the pressure, velocity and temperature of the exhaust gas inside the manifold, with an inlet mass flow rate of 0.000424 kg/s at 900 K.
Get the Exhaust Manifold Project
Want this project for your final year, mini project or M.Tech work? Message us with your university, branch and deadline, and we will share the exact scope, files and report format.
Enquire about this project on WhatsApp or use the enquiry form on our home page. Browse more mechanical projects or 60+ mechanical engineering project ideas.
Interested in this project? Get the details, files and guidance from our team.
Enquire on WhatsApp