CFD, Static and Thermal Analysis of a Steam Boiler Used in Power Plants with Steel, Brass and Steel 316L (SolidWorks and ANSYS)

A steam boiler is a closed vessel in which water is heated until it turns into steam. In a thermal power plant, this high-pressure steam drives a turbine connected to a generator; after the turbine, the steam is cooled and condensed back into water, which returns to the boiler to start the cycle again. Because the boiler works at very high pressure and temperature, its walls and tubes must be strong enough not to burst and must also transfer heat efficiently. This project studies a steam boiler with three different materials using static, thermal and CFD analysis to find the most suitable material.

Steam boiler 3D model in SolidWorks

How a Steam Boiler Works

Fuel such as coal, gas or biomass is burned in a furnace, and the hot combustion gases pass over or through a set of tubes. Water or steam flows on the other side of the tube walls and absorbs the heat. In a fire tube boiler, the hot gases flow inside the tubes surrounded by water, while in a water tube boiler, water flows inside the tubes surrounded by hot gases. Either way, the boiler shell and tubes must hold the internal steam pressure safely, and the tube material should allow heat to pass through without large losses to the surroundings.

About the Project

The boiler shell, internal tubes and nozzles are modelled in SolidWorks using real-time dimensions and assembled into a complete boiler. The assembly is imported into ANSYS Workbench and meshed. Three types of analysis are then carried out for three materials: steel, brass and Steel 316L.

  • Static structural analysis: an internal pressure of 45 MPa is applied on the inner surface of the boiler to find total deformation, stress, strain and safety factor.
  • Steady-state thermal analysis: temperature and heat flux are calculated to see how much heat each material lets out of the vessel.
  • CFD analysis in ANSYS Fluent: steam flow through the boiler is simulated at four inlet velocities, 15, 30, 45 and 60 m/s, to find pressure, temperature, velocity and heat transfer coefficient.

The heat transfer coefficients found in the CFD analysis are also used as inputs to the thermal analysis, so the two studies are linked.

Steam boiler mesh in ANSYS
Meshing (ANSYS)

Software Used

  • SolidWorks: 3D modelling of the boiler shell, tubes and assembly
  • ANSYS Static Structural: deformation, stress, strain and safety factor
  • ANSYS Steady-State Thermal: temperature and heat flux
  • ANSYS Fluent: CFD analysis of steam flow at different velocities

Analysis Results

Steam boiler internal pressure boundary condition in ANSYS
Internal pressure of 45 MPa applied (ANSYS)
Steam boiler thermal analysis result in ANSYS
Thermal analysis result (ANSYS)

Key Results (Preview)

ResultSteelBrassSteel 316L
Total deformation (mm)0.0763270.129590.079202
Equivalent stress (MPa)164.19164.73164.06
Safety factor1.52261.76041.8286
Heat flux (W/mm²)0.653430.995480.34676

The boiler can withstand 45 MPa of internal pressure with all three materials. The heat flux results show large differences: a material with high heat flux loses more heat from the vessel to the atmosphere, which reduces efficiency. The CFD results at each velocity and the final recommended material, with its advantages and limitations, are explained in the report.

Why This Project Matters

Boilers are at the heart of thermal power plants, sugar mills, refineries, textile and food industries. Choosing the right material affects safety, efficiency and maintenance cost over decades of service. This project combines pressure vessel design, heat transfer and fluid flow in one complete study, which makes it an excellent final year or M.Tech project for thermal and mechanical engineering students.

Related Projects

Explore more design and analysis projects on similar topics:

What You Get

  • Design files: SolidWorks models of the boiler shell, tubes and full assembly (with STEP files)
  • Analysis files: ANSYS static structural, steady-state thermal and Fluent CFD files at all four steam velocities
  • Project document: complete report with methodology, results and conclusion
  • Class explanation: a session that explains what was done in the project, step by step, so you can understand and present it confidently

Who Is This Project For?

This project suits B.Tech and B.E. final year students, diploma students looking for a strong design and analysis project, and M.Tech students who need a base model they can extend for their thesis. It is also useful for anyone who wants to learn pressure vessel analysis, thermal analysis and CFD of steam flow in ANSYS on a real engineering problem instead of a textbook example.

Frequently Asked Questions

What is the difference between a fire tube and a water tube boiler?

In a fire tube boiler, hot combustion gases flow inside the tubes and the water surrounds them. In a water tube boiler, water flows inside the tubes and the hot gases flow around them. Water tube boilers handle higher pressures and are common in large power plants.

What internal pressure is applied in the static analysis?

An internal pressure of 45 MPa is applied on the inner surface of the steam boiler. The analysis checks the total deformation, stress, strain and safety factor for each material at this pressure.

At which steam velocities is the CFD analysis done?

The steam flow is simulated in ANSYS Fluent at four inlet velocities: 15 m/s, 30 m/s, 45 m/s and 60 m/s. The heat transfer coefficients from these CFD runs are also used as inputs to the thermal analysis.

Which materials are compared for the boiler?

Steel, brass and Steel 316L are compared. The study looks at both strength under pressure and heat flux, because a material that loses too much heat to the atmosphere reduces the efficiency of the boiler.

Get the Steam Boiler CFD and Thermal Analysis Project

Want this project for your final year, mini project or M.Tech work? Message us with your university, branch and deadline, and we will share the exact scope, files and report format.

Enquire about this project on WhatsApp or use the enquiry form on our home page. Browse more mechanical projects or 60+ mechanical engineering project ideas.

Interested in this project? Get the details, files and guidance from our team.

Enquire on WhatsApp

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top